---
discourse: 8355
---

(devices-proxy)=
# Type: `proxy`

```{youtube} https://www.youtube.com/watch?v=IbAKwRBW8V0
```

```{note}
The `proxy` device type is supported for both containers (NAT and non-NAT modes) and VMs (NAT mode only).
It supports hotplugging for both containers and VMs.
```

Proxy devices allow forwarding network connections between host and instance.
This method makes it possible to forward traffic hitting one of the host's addresses to an address inside the instance, or to do the reverse and have an address in the instance connect through the host.

In {ref}`devices-proxy-nat-mode`, a proxy device can be used for TCP and UDP proxying.
In non-NAT mode, you can also proxy traffic between Unix sockets (which can be useful to, for example, forward graphical GUI or audio traffic from the container to the host system) or even across protocols (for example, you can have a TCP listener on the host system and forward its traffic to a Unix socket inside a container).

The supported connection types are:

- `tcp <-> tcp`
- `udp <-> udp`
- `unix <-> unix`
- `tcp <-> unix`
- `unix <-> tcp`
- `udp <-> tcp`
- `tcp <-> udp`
- `udp <-> unix`
- `unix <-> udp`

To add a `proxy` device, use the following command:

    lxc config device add <instance_name> <device_name> proxy listen=<type>:<addr>:<port>[-<port>][,<port>] connect=<type>:<addr>:<port> bind=<host/instance_name>

```{tip}
Using a proxy device in NAT mode is very similar to adding a {ref}`network forward <network-forwards>`.

The difference is that network forwards are applied on a network level, while a proxy device is added for an instance.
In addition, network forwards cannot be used to proxy traffic between different connection types.
```

(devices-proxy-nat-mode)=
## NAT mode

The proxy device also supports a NAT mode (`nat=true`), where packets are forwarded using NAT rather than being proxied through a separate connection.
This mode has the benefit that the client address is maintained without the need for the target destination to support the HAProxy PROXY protocol (which is the only way to pass the client address through when using the proxy device in non-NAT mode).

However, NAT mode is supported only if the host that the instance is running on is the gateway (which is the case if you're using `lxdbr0`, for example).

In NAT mode, the supported connection types are:

- `tcp <-> tcp`
- `udp <-> udp`

When configuring a proxy device with `nat=true`, you must ensure that the target instance has a static IP configured on its NIC device.

## Specifying IP addresses

Use the following command to configure a static IP for an instance NIC:

    lxc config device set <instance_name> <nic_name> ipv4.address=<ipv4_address> ipv6.address=<ipv6_address>

To define a static IPv6 address, the parent managed network must have `ipv6.dhcp.stateful` enabled.

When defining IPv6 addresses, use the square bracket notation, for example:

    connect=tcp:[2001:db8::1]:80

You can specify that the connect address should be the IP of the instance by setting the connect IP to the wildcard address (`0.0.0.0` for IPv4 and `[::]` for IPv6).

```{note}
The listen address can also use wildcard addresses when using non-NAT mode.
However, when using NAT mode, you must specify an IP address on the LXD host.
```

## Device options

`proxy` devices have the following device options:

% Include content from [../metadata.txt](../metadata.txt)
```{include} ../metadata.txt
    :start-after: <!-- config group device-proxy-device-conf start -->
    :end-before: <!-- config group device-proxy-device-conf end -->
```

## Configuration examples

Add a `proxy` device that forwards traffic from one address (the `listen` address) to another address (the `connect` address) using NAT mode:

    lxc config device add <instance_name> <device_name> proxy nat=true listen=tcp:<ip_address>:<port> connect=tcp:<ip_address>:<port>

Add a `proxy` device that forwards traffic going to a specific IP to a Unix socket on an instance that might not have a network connection:

    lxc config device add <instance_name> <device_name> proxy listen=tcp:<ip_address>:<port> connect=unix:/<socket_path_on_instance>

Add a `proxy` device that forwards traffic going to a Unix socket on an instance that might not have a network connection to a specific IP address:

    lxc config device add <instance_name> <device_name> proxy bind=instance listen=unix:/<socket_path_on_instance> connect=tcp:<ip_address>:<port>

See {ref}`instances-configure-devices` for more information.