--- discourse: 10034,9953 --- (network-bridge-firewall)= # How to configure your firewall ````{only} diataxis ```{important} This guide applies to managed bridge networks only. ``` ```` Linux firewalls are based on `netfilter`. LXD uses the same subsystem, which can lead to connectivity issues. If you run a firewall on your system, you might need to configure it to allow network traffic between the managed LXD bridge and the host. Otherwise, some network functionality (DHCP, DNS and external network access) might not work as expected. You might also see conflicts between the rules defined by your firewall (or another application) and the firewall rules that LXD adds. For example, your firewall might erase LXD rules if it is started after the LXD daemon, which might interrupt network connectivity to the instance. ## `xtables` vs. `nftables` There are different userspace commands to add rules to `netfilter`: `xtables` (`iptables` for IPv4 and `ip6tables` for IPv6) and `nftables`. `xtables` provides an ordered list of rules, which might cause issues if multiple systems add and remove entries from the list. `nftables` adds the ability to separate rules into namespaces, which helps to separate rules from different applications. However, if a packet is blocked in one namespace, it is not possible for another namespace to allow it. Therefore, rules in one namespace can still affect rules in another namespace, and firewall applications can still impact LXD network functionality. If your system supports and uses `nftables`, LXD detects this and switches to `nftables` mode. In this mode, LXD adds its rules into the `nftables`, using its own `nftables` namespace. ## Use LXD's firewall By default, managed LXD bridges add firewall rules to ensure full functionality. If you do not run another firewall on your system, you can let LXD manage its firewall rules. To enable or disable this behavior, use the `ipv4.firewall` or `ipv6.firewall` {ref}`configuration options `. ## Use another firewall Firewall rules added by other applications might interfere with the firewall rules that LXD adds. Therefore, if you use another firewall, you should disable LXD's firewall rules. You must also configure your firewall to allow network traffic between the instances and the LXD bridge, so that the LXD instances can access the DHCP and DNS server that LXD runs on the host. See the following sections for instructions on how to disable LXD's firewall rules and how to properly configure `firewalld` and UFW, respectively. ### Disable LXD's firewall rules Run the following commands to prevent LXD from setting firewall rules for a specific network bridge (for example, `lxdbr0`): lxc network set ipv6.firewall false lxc network set ipv4.firewall false ### `firewalld`: Add the bridge to the trusted zone To allow traffic to and from the LXD bridge in `firewalld`, add the bridge interface to the `trusted` zone. To do this permanently (so that it persists after a reboot), run the following commands: sudo firewall-cmd --zone=trusted --change-interface= --permanent sudo firewall-cmd --reload For example: sudo firewall-cmd --zone=trusted --change-interface=lxdbr0 --permanent sudo firewall-cmd --reload ```{warning} The commands given above show a simple example configuration. Depending on your use case, you might need more advanced rules and the example configuration might inadvertently introduce a security risk. ``` ### UFW: Add rules for the bridge If UFW has a rule to drop all unrecognized traffic, it blocks the traffic to and from the LXD bridge. In this case, you must add rules to allow traffic to and from the bridge, as well as allowing traffic forwarded to it. To do so, run the following commands: sudo ufw allow in on sudo ufw route allow in on sudo ufw route allow out on For example: sudo ufw allow in on lxdbr0 sudo ufw route allow in on lxdbr0 sudo ufw route allow out on lxdbr0 ````{warning} % Repeat warning from above ```{include} network_bridge_firewalld.md :start-after: :end-before: ``` Here's an example for more restrictive firewall rules that limit access from the guests to the host to only DHCP and DNS and allow all outbound connections: ``` # allow the guest to get an IP from the LXD host sudo ufw allow in on lxdbr0 to any port 67 proto udp sudo ufw allow in on lxdbr0 to any port 547 proto udp # allow the guest to resolve host names from the LXD host sudo ufw allow in on lxdbr0 to any port 53 # allow the guest to have access to outbound connections CIDR4="$(lxc network get lxdbr0 ipv4.address | sed 's|\.[0-9]\+/|.0/|')" CIDR6="$(lxc network get lxdbr0 ipv6.address | sed 's|:[0-9]\+/|:/|')" sudo ufw route allow in on lxdbr0 from "${CIDR4}" sudo ufw route allow in on lxdbr0 from "${CIDR6}" ``` ```` (network-lxd-docker)= ## Prevent connectivity issues with LXD and Docker Running LXD and Docker on the same host can cause connectivity issues. A common reason for these issues is that Docker sets the global FORWARD policy to `drop`, which prevents LXD from forwarding traffic and thus causes the instances to lose network connectivity. See [Docker on a router](https://docs.docker.com/network/iptables/#docker-on-a-router) for detailed information. There are different ways of working around this problem: Uninstall Docker : The easiest way to prevent such issues is to uninstall Docker from the system that runs LXD and restart the system. You can run Docker inside a LXD container or virtual machine instead. See [Running Docker inside of a LXD container](https://www.youtube.com/watch?v=_fCSSEyiGro) for detailed information. Enable IPv4 forwarding : If uninstalling Docker is not an option, enabling IPv4 forwarding before the Docker service starts will prevent Docker from modifying the global FORWARD policy. LXD bridge networks enable this setting normally. However, if LXD starts after Docker, then Docker will already have modified the global FORWARD policy. ```{warning} Enabling IPv4 forwarding can cause your Docker container ports to be reachable from any machine on your local network. Depending on your environment, this might be undesirable. See [local network container access issue](https://github.com/moby/moby/issues/14041) for more information. ``` To enable IPv4 forwarding before Docker starts, ensure that the following `sysctl` setting is enabled: net.ipv4.conf.all.forwarding=1 ```{important} You must make this setting persistent across host reboots. One way of doing this is to add a file to the `/etc/sysctl.d/` directory using the following commands: echo "net.ipv4.conf.all.forwarding=1" > /etc/sysctl.d/99-forwarding.conf systemctl restart systemd-sysctl ``` Allow egress network traffic flows : If you do not want the Docker container ports to be potentially reachable from any machine on your local network, you can apply a more complex solution provided by Docker. Use the following commands to explicitly allow egress network traffic flows from your LXD managed bridge interface: iptables -I DOCKER-USER -i -j ACCEPT iptables -I DOCKER-USER -o -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT For example, if your LXD managed bridge is called `lxdbr0`, you can allow egress traffic to flow using the following commands: iptables -I DOCKER-USER -i lxdbr0 -j ACCEPT iptables -I DOCKER-USER -o lxdbr0 -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT ```{important} You must make these firewall rules persistent across host reboots. How to do this depends on your Linux distribution. ```